METALS MAINTENANCE
The capability of steel products to withstand atmospheric agents and saline
mist (areas close to the sea) depends strictly on events and actions that can
cause a decay of performance of the product (lower the resistance to oxidation).
Factors that make steel products more vulnerable are the following:
- Lack of ordinary mainteinance (both for products treated with cataphoresis
and for products treated with C5M), following given instructions;
- Damage of the varnish film caused by scraping the product on rough surfaces
(eg uneven floors), by scratches, dents or abrasions.
- Chemical agression, solvents (acetone, nitro or other) acids (solphoric, cloridic or other) alkaline (caustic soda or other) abrasive detergents.
- Direct exposure to flames.
Product subject to even one of the previous actions, could show a deterioration
of the qualitative and aesthetic characteristics in terms of the risk in oxidation.
In case of damage and / or removal of the varnish, with consequent stripping of
the steel structure and appearance of oxidation (rust), we suggest to promptly
restore the finish and the surface protection using the FINISHING RESTORATION KIT according to the following cycle:
Note: The Finishing Restoration Kit is supplied with the paint necessary for the
restoration with or without catalyst, respectively applicable with spray gun or
spray can, depending on the type of product finish (granular or opaque).
ISO standards (BS EN ISO 12944-8 for paints and varnishes - BS EN ISO 14713
for zinc coatings) set guidelines for corrosion protection of steel. In order to
maintain the effectiveness of this feature, it is highly recommended to execute
the following procedures during product life-time:
ORDINARY MAINTENANCE FOR PRODUCTS TREATED WITH CATAPHORESIS
-Use low pressure cold water, at least 4 times a year.
-Use hot water (50-60° C) and 3,5-4 bar pressure twice a year.
ORDINARY MAINTENANCE FOR PRODUCTS TREATED WITH C5M
- Use low pressure cold water, at least 3 times a year.
- Use hot water (50-60° C) and 3,5-4 bar pressure once a year.
The correct execution of ordinary maintenance determines the best conditions
for the durability of the product and maintains the characteristics of protectionof
the steel intact over time. Omitting or limiting maintenance actions can accelerate product degradation.
DECAY OF PERFORMANCE
CLEANING AND MAINTENANCE
• Clean the area where the paint is no
longer present or damaged, eliminating dirt and any residues.
• Apply converter with the appropriate brush (see Note below).
• Pay attention to completely cover
the area to be restored.
• Let dry for at least 15 min.
• Paint with spray gun or spray can.
If necessary, apply two coats of varnish to obtain higher covering and
protective effect.
• Let dry for at least 2 hours.
PHASE 6
PHASE 5
PHASE 4
PHASE 3
PHASE 2
PHASE 1
15 min
120 min
Ceramic
Ceramic tops do not require any particular maintenance, thanks to the high resistance and stability of the material.
Cleaning can be carried out very simply using soft and clean cloths soaked in
water, possibly adding detergents of common household use with neutral pH or
natural vinegar.
Dry the surface after cleaning is complete. Do not use metal or abrasive brushes.
The use of products containing waxes, brighteners, strong acids (eg hydrofluoric,
sulfuric, etc.) is not recommended because they could permanently damage the
surface.
TYPE OF STAIN FIRST OPERATION SECOND OPERATION
Cement, limestone, metal scratch,
rust.
Clean with water as soon as
possible, softly rubblig with
a cloth
Fila Deterdeck, cement descaler
Grease, food, rubber, dye, marking
pen, blood, etc.
Clean with water as soon as
possible, gently rubblig with
a cloth
Fila PS87
Graffiti, varnish, paint Clean with water as soon as
possible, gently rubblig with
a cloth
Fila NoPaint Star, solvent
Coffee, tea, juice, soda Clean with water as soon as
possible, gently rubblig with
a cloth
Fila NoPaint Star, solvent
Candle wax or wax for scratch repairs,
tree resin or adhesive tape traces
Clean with water as soon as
possible, gently rubblig with
a cloth
Filasolv, solvent
Silicone sealant Clean with water as soon as
possible, gently rubblig with
a cloth
Fila Zero Sil, acetone
HPL
KIND OF IMPURITY/DIRT WHAT YOU NEED CLEANING METHOD
dust, pencil, coffee, tea, fruit juice,
syrups, jam, milk.
absorbent paper Apply the detergent. Allow it to work
for a short time according to the
degree of the dirt. Remove the
detergent with a sponge, rinse and
wipe off with absorbent paper/cloth.
soft cloth
sponge
non abrasive detergents
water
limescale traces and marks absorbent paper Apply the detergent (it may contain acetic acid or
citric acid 10% max.solution). Allow it to work for
a short time according to the degree of the dirt.
Remove the detergent
with a sponge, rinse and wipe off with absorbent
paper/cloth.
soft cloth
sponge
non abrasive detergents
water
grease, oil, fingerprints, felt-tip pens,
ballpoint pen ink, rubber marks, tar
traces, wine, liquors, lipstick, face
powder, nail polish, shoe cream,
floor wax
absorbent paper Use a detergent and/or proper organic solvents
(acetone, ethyl alcohol, benzine, perchloroethylene, MEK-methyl ethyl ketone, etc.). Allow it to work
for a short time according to the degree of the dirt.
Remove the detergent or the organic solvent with
the sponge, rinse and dry wipe with paper/cloth.
soft cloth
sponge
non abrasive detergents
water
organic solvents
traces of candle wax wooden or synthetic palette
knife
Remove the hardened wax with the
palette knife. Wipe off any residue
with hot water and dry wipe
afterwards with absorbent paper. absorbent paper
water
bacteriological traces (blood, urine,
faeces, pathogenic germs, etc.)
absorbent paper Apply water and soap and/or water
and detergent.
Allow it to work for a short time
according to the degree of the dirt.
Remove the soap/detergent with a
sponge, rinse and dry wipe with
absorbent paper. Sanitize with
disinfectant products and/or steam.
Dry wipe.
soft cloth
sponge
non abrasive detergents
liquid or solid soap
disinfectant products
water
paint sprinkles and traces containing
solvents, dye stains, glue, adhesive
traces coming from the removal of
laminate protective films
soft cloth Apply a proper organic solvent
(acetone, ethyl alcohol, benzine,
perchloroethylene, MEK-methyl
ethyl ketone, etc.) Allow it to work
for a short time according to the
degree of the dirt. Remove the
organic solvent, soap, rinse and dry
wipe with absorbent paper or cloth.
organic solvents
liquid or solid soap
absorbent paper
water
silicone rubber cement or other
silicone products traces
these substances should not be left in contact with
the laminate surface for a long period of time
